lf-xx flex connectsystem for linearlight flex data sheet benefits universal feeder and connector for linearlight flex modules with 8mm width ? assembly without tools ? reduced assembly time ? highly shock resistant ? applications connect system for linearlight flex modules, linearlight power flex, 8mm width ? product technical operating data and ordering guide ean * s-unit * max voltage [v] max current [a] diameter of wire [mm2 / awg] length of wire [mm] lf-2pin flex 4008321955326 100 25 3 0,14 500 24 / lf-2term flex 4008321955357 200 0,15 - - - / lf-conn-10 flex 4008321955333 200 25 3 0,057 10 30 / lf-conn-150 flex 4008321955340 200 25 3 0,057 150 30 / ean: bag containing 10 pieces s-unit: modules per shipping unit *) technical features feeder lf-2pin flex for connection of all linearlight flex width 8mm with the power supply ? board to board connection of two flex modules: lf-conn-10 flex for short gaps, lf-conn-150 flex for longer gaps ? allowed operating temperature suited to all linearlight flex products ? additional cutting possibilities by using the termination lf-2term for all single colour linearlight flex with 8mm width ? connection possible at the reel end or at the cut points ? locking system meets shock and vibration requirements according to iec 60068-2-6/27 ? use only in indoor applications or in luminaires with ip67 rating ? backside of lf-2term is self-adhesive ? page 1 of 3 lf-xx flex - 08.12.2009
drawings lf-2pin flex housing pps / polyamide / black isolation of wires pvc / black/red lf-2term flex housing pps / polyamide / black isolation of wires lf-conn-10 flex housing pps / polyamide / black isolation of wires aramid paper / white lf-conn-150 flex housing pps / polyamide / black isolation of wires aramid paper / white page 2 of 3 lf-xx flex - 08.12.2009
sales and technical support sales and technical support is given by the local osram subsidiaries. on our world wide homepage all osram subsidiaries are listed with complete address and phone numbers. osram gmbh hellabrunner strasse 1 d - 81536 mnchen germany www.osram.com +49 (0)89 6213-0 related and further information the new dimension of light ? 153 s006 gb www.osram.com/led-systems-downloads optotronic? technical guide ? 130 t008 gb www.osram.com/ecg-downloads optotronic? data sheets ? http://catalog.myosram.com osram led systems ? www.osram.com/led-systems new standards for led control gear ? 130 w011 gb www.osram.com/ecg-download datasheets for lf05a, lf05e, lf06p ? 153 s006 gb www.osram.com/led-systems-downloads safety information installation of led modules (with power supplies) needs to be made with regard to all applicable electrical and safety standard s. only qualified personnel should be allowed to perform installations. ? ? all components of the connectsystem flex must be assembled to avoid any stress on the wires and/or board connectors. the installer must ensure that there is adequate strain relief between the board connection and the wiring. ? in order to maintain adequate electrical contact, please refrain from repeat removal, maximum of 5, of the connectsystem flex. ? the connector has no inverse polarity protection. there will be no electrical function if connector is not well positioned or i f polarity is inverse. several modules can be damaged (see the respective module data sheet). ? the maximum operation current on page 1 may not be exceeded. ? the connectsystem flex is designed for indoor application only. any unprotected outdoor use is not allowed. ? a suitable enclosure ip67 is required if the system is to be exposed to humidity and /or dust. condensation water in the ip67 enclosure is not allowed. ? especially when used with linearlight power flex the lf-2term can overheat. the maximum temperature measured at the "up"- label is 65c. the lf-2term has to be adhered to a thermoconducting surface. assembly information ? for electrical connection of the linearlight flex modules open the locker by pulling and place the module in the slot. the "up" mark of the connectsystem flex must face towards to front si de of the led module for an electrical connection between the solder pads and the connectsystem flex. the connectsystem flex is locked by pushing locking bar back. ? pay attention to the correct polarity between feeder lf-2pin flex and led module: - for the feeder lf-2pin flex connect the black cable to th e '-' pole and the red cable to the '+' pole of the module ? particular attention is required when using the connector for bo ard to board connection: the '+' pole of the first module has t o be connected to the '+' pole of the second module. in case of wrong polarity no light will be emitted and the moules can be damage d (see the respective module data sheet). ? the lf-2term can be used at any section cut point intended for it. these points are marked on the module. page 3 of 3 lf-xx flex - 08.12.2009
|
